banner
May 10, 2022
0 View
0 0

5 100% ways to propagate plants by layering

5 100% ways to propagate plants by layering

Usually, the method of germinating seedlings from cuttings, or grafting on a stock, is used for plant propagation. But these methods are not always successful. It is guaranteed that the plant can be propagated only by layering. It allows you to get genetically 100% the same plant.

1. Simple layering in the ground

5 100% ways to propagate plants by layering

This method works great on shrubs. They can propagate currants, gooseberries, etc. Take a branch and remove its bark in a circle, exposing a few centimeters of wood. Then dig this cut with soil. You can also put a load on top so that the branch does not rise again.

5 100% ways to propagate plants by layering
5 100% ways to propagate plants by layering

Above the ground we leave the top of the branch with leaves. Now we wait 4 weeks. Be sure to regularly water the layers in the place of the cut bark. In a month he will give roots. It can be cut off and planted in a new place.

5 100% ways to propagate plants by layering

2. Escape in the ground

You can also take the tip of a young shoot and dig it on the side of the main plant. As a result, roots will appear on the edge, and then the shoot will break through above the ground with new leaves. Later it can be cut off from the mother plant and planted separately.

5 100% ways to propagate plants by layering

5 100% ways to propagate plants by layering

3. Layering canopy

This mode of reproduction differs between monocots and dicots. To form a new plant in a monocot, make an oblique cut down the branch without cutting a third of its diameter.

Insert matches, plastic sticks, or other objects across the notch to prevent the chips from coming back together. Then put some moistened substrate on a plastic bag and lean it against the cut.

5 100% ways to propagate plants by layering

It is necessary to wrap the polyethylene, and tightly tie it around the edges. Thus, we get a bag of soil in which the root will sprout. If sunlight hits it strongly, then the bag must be covered with foil.

5 100% ways to propagate plants by layering

In dicotyledonous plants, it is not necessary to make an incision, but to remove a ring of bark 2 cm wide. Both the upper rough bark and the green cambium under it are cut off. Then the bag with the substrate is wound, as is the case with monocotyledonous plants. When the roots sprout in the bag, the branch is cut off and planted separately.

5 100% ways to propagate plants by layering

4. Layering in a pot

First, we prepare an incision on the branch or remove the bark, depending on which plant we are working with. Next, we put a pot on the branch, cut along one side.

5 100% ways to propagate plants by layering
5 100% ways to propagate plants by layering

The cut of the pot is glued with adhesive tape, and tied with a rope. Then soil is poured into it. Thus, we grow the root as in the previous method. But here the soil will have to be watered. If you close the pot with a bag, then this will have to be done less often.

5 100% ways to propagate plants by layering

5. Layering in water

You can also make an oblique cut on a branch to get a long sliver. Next, we take a PET bottle, and cut a hole in it from the side. Insert a stick into it.

5 100% ways to propagate plants by layering
5 100% ways to propagate plants by layering

Then fill the bottle with water so as to cover the sliver. Tie the bottle, and cover with something dark. It remains to periodically add water until the root appears. To speed up rooting, you can add a growth stimulant or a quarter of an aspirin tablet to the water.

5 100% ways to propagate plants by layering
5 100% ways to propagate plants by layering

Watch the video

Article Categories:
Interesting
banner

Leave a Reply